ADAM27P16G Datasheet – 4-Bit Single Chip Microcomputer
Package SOP 16 Pin Type
ADAM27P16G overview
The ADAM27P16G is a 4-Bit Single Chip Microcomputer made by ABOV Semiconductor, supplied in an SOP 16 Pin Type package. The absolute maximum ratings table on this page lists the 5 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the ADAM27P16G pinout and maximum ratings, with the full datasheet PDF to preview below or download.
The ADAM27PXX is remote control transmitter which uses CMOS technology. The ADAM27PXX is suitable for remote control of TV, VCR, FANS, Air conditioners, Audio Equipment's, Toys, Games etc. The ADAM27PXX is MTP version.
Datasheet
adam27p08-datasheet.pdf
ADAM27P16G features
- Program memory2,048 bytes (2,048 x 8bit) MTP(Multi Time Programming) : 1K * 2, 2K * 1
- 2,048 bytes (2,048 x 8bit)
- MTP(Multi Time Programming) : 1K * 2, 2K * 1
- Data memory (RAM) 32 nibble (32 x 4bit)
- 32 nibble (32 x 4bit)
- 3 levels of subroutine nesting
- 8-bit Table Read Instruction
- Oscillator Type (Operating frequency) Internal RC Oscillator (typically 3.64MHz)
- Internal RC Oscillator (typically 3.64MHz)
- Instruction cycle fOSC/48
- fOSC/48
- Stop mode
- Released stop mode by key input
- Built in Power-on Reset circuit
- Built in Transistor for I.R LED Drive IOL=250mA at VDD=3V and VO=0.3V
- IOL=250mA at VDD=3V and VO=0.3V
- Built in Low Voltage reset circuit
- Built in a watch dog timer (WDT)
- Low operating voltage 1.8 ~ 3.6V
- 1.8 ~ 3.6V
- 8/16-SOP Package
ADAM27P16G pinout
| Name | Description |
|---|---|
| K0 ~ K3 R0 ~ R2 | -. 4-bit I/O port. (Input mode is set only when each of them output `H`) -. Each pin has STOP mode release function in input mode. -. Output mode is set when each of them output `L`. -. When used as `output`, each pin can be set and reset independently. -. When set as the input mode, input state of |
| P0 ~ P3 | -. 4-bit I/O port. (Input mode is set only when each of them output `H`) -. Each pin has STOP mode release function in input mode. -. Output mode is set when each of them output `L`. -. When used as `output`, each pin can be set and reset independently. -. When T-key Scan is disabled, P0~P3 are forc |
| CS0~CS1 | -. 2-bit I/O port. (Input mode is set only when each of them output `H` and pull-up is enabled.) -. Pull-ups can be enabled by user program. -. Output mode is set when each of them output `L`, or when it’s pull-up is disabled. -. When used as `output`, each pin can be set and reset independently. -. |
| ROUT | -. High Current Pulse Output. -. N-ch open drain output. |
| VDD | -. Positive power supply. |
| GND | -. Ground |
Absolute maximum ratings
| Parameter | Symbol | Value | Unit |
|---|---|---|---|
| Supply Voltage | VDD | -0.3 ~ 5.0 | V |
| Power dissipation | PD | 700* | ㎽ |
| Input voltage | VIN | -0.3 ~ VDD+0.3 | V |
| Output voltage | VOUT | -0.3 ~ VDD+0.3 | V |
| Storage Temperature | TSTG | -65 ~ 150 | ℃ |
ADAM27P16G applications
- Industrial Automation
- Networking Equipment
- Automotive Electronics
- Wearable Devices
Comments 0
Leave a comment