ESP-09 ESP8266 Serial WiFi Module
ESP-09 overview
The ESP-09 is an ESP8266 Serial WiFi Module, supplied in a QFN-32 package. Main ratings: Working voltage 3.3V; Supported voltage 3.0 - 3.6V; Working current 71-80mA; Maximum current 300mA. This page brings together the ESP-09 pinout and key specifications, with the full datasheet PDF to preview below or download.
ESP-09 ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or offload all Wi-Fi networking functions from another application processor. The module has powerful onboard processing and storage capabilities that allow it to be integrated with the sensors and other application-specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. ESP-09 ESP8266 with direct aid from various interfaces, supports UART, IIC, PWM, GPIO, ADC, etc., allowing it to be suitable for a wide array of networking applications
ESP-09 demonstrates sophisticated system-level features including fast sleep/wake, context switching for energy-efficient VoIP, adaptive radio biasing for low-power operation, advanced signal processing, and spur cancellation with radio co-existence features for common cellular, Bluetooth, DDR, LVDS, LCD interference mitigation.
Key specifications
Datasheet
ESP-09 features
- 802.11 b / g / n
- Built Tensilica L106 ultra-low power 32-bit micro-MCU, support 80 MHz clock speed and 160 MHz, support for RTOS
- Built-in 10-bit precision ADC
- Built-in TCP / IP protocol stack
- Built-TR switch, balun, LNA, power amplifier, and matching network
- Built-in PLL, regulator, and power management components, 802.11b mode +20 dBm output power
- WiFi @ 2.4 GHz, supports WPA / WPA2 security mode
- Support remote upgrade and AT Cloud OTA upgrade
- Support STA / AP / STA + AP mode
- Support Smart Config function (including Android and iOS)
- HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
- Deep sleep holding current 10 uA, shutdown current is less than 5 uA
- within 2 ms of wake-up, connect and transfer data packets
- Standby power consumption is less than 1.0 mW (DTIM3)
ESP-09 pinout
| Pin | Name | Description |
|---|---|---|
| 1 | GND | Ground Pin |
| 2 | ANT | Antenna Pin |
| 3 | Vcc | Chip Supply Voltage (3.3V) |
| 4 | CH_EN | Chip Enable Pin |
| 5 | GND | Ground Pin |
| 6 | GPIO14 | General Purpose I/O 14 |
| 7 | GPIO12 | General Purpose I/O 12 |
| 8 | GPIO13 | General Purpose I/O 13 |
| 9 | GND | Ground Pin |
| 10 | GPIO15 | General Purpose I/O 15 |
| 11 | GPIO2 | General Purpose I/O 2 |
| 12 | GPIO0 | General Purpose I/O 0 |
| 13 | GND | Ground Pin |
| 14 | GPIO3 | General Purpose I/O 3 |
| 15 | GPIO1 | General Purpose I/O 1 |
| 16 | RST | Reset Pin |
| 17 | GND | Ground Pin |
| 18 | GND | Ground Pin |
| 19 | GND | Ground Pin |
| 20 | GND | Ground Pin |
ESP-09 specifications
| Working voltage | 3.3V |
|---|---|
| Supported voltage | 3.0 - 3.6V |
| Working current | 71-80mA |
| Maximum current | 300mA |
| Shallow sleep current | 2mA |
| Deep sleep current | 0.02mA |
| Operating frequency | 26MHz |
| Flash memory | 8 MB / 1 MB |
| WiFi Protocols | 802.11b/g/n |
| Frequency range | 2.4GHz-2.5GHz (2412M-2484M) |
| WiFi Modes | Client, Soft AP, Client+Soft AP (station, softAP, station+softAP) |
| Security | WPA-PSK, WPA2-PSK |
| Encryption | WEP, TKIP, AES |
| Network protocols | IPv4, TCP/UDP/HTTP/FTP |
| General Purpose Pins (In/Out, GPIO) | 8 |
| Maximum current per general purpose contact | 12mA, recommended 6mA |
| Output power in 802.11b mode | +20dBm |
| Interfaces | UART, GPIO, HSPI, I2C, I2S |
| Baud rate | 300-4608000 baud, default 115200 baud |
| Built-in blocks | network matching, phase-locked loop, power management, regulation blocks |
| Pin type | solder pads |
| Operating temperature | -20°...+85° |
| Dimensions | 10.1 x 10.1 x 1.7 mm |
ESP-09 applications
- Access points portals
- IoT projects
- Wireless data logging
- Used in learning the networking fundamentals
Comments 0
Leave a comment