F16-100HIP Datasheet – 16Mbit Serial Flash Memory
16 Megabit Serial Flash Memory with 4Kbytes Uniform Sector
F16-100HIP overview
The F16-100HIP is a 16 Megabit Serial Flash Memory with 4Kbytes Uniform Sector, supplied in an 8-pin 200mil SOP Type package. The absolute maximum ratings table on this page lists the 5 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the F16-100HIP pinout and maximum ratings, with the full datasheet PDF to preview below or download.
The EN25F16 is a 16M-bit (2048K-byte) Serial Flash memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus. The memory can be programmed 1 to 256 bytes at a time, using the Page Program instruction. The EN25F16 is designed to allow either single Sector at a time or full chip erase operation. The EN25F16 can be configured to protect part of the memory as the software protected mode. The device can sustain a minimum of 100K program/erase cycles on each sector.
Datasheet
F16-100HIP features
- Single power supply operation Full voltage range: 2.7-3.6 volt
- Full voltage range: 2.7-3.6 volt
- 16 Mbit Serial Flash 16 M-bit/2048 K-byte/8192 pages 256 bytes per programmable page
- 16 M-bit/2048 K-byte/8192 pages
- 256 bytes per programmable page
- High performance 100MHz clock rate
- 100MHz clock rate
- Low power consumption 5 mA typical active current 1 A typical power down current
- 5 mA typical active current
- 1 A typical power down current
- Uniform Sector Architecture
- 512 sectors of 4-Kbyte
- 32 blocks of 64-Kbyte
- Any sector or block can be erased individually
- Software and Hardware Write Protection
- Write Protect all or portion of memory via software
- Enable/Disable protection with WP# pin
- High performance program/erase speed
- Page program time: 1.5ms typical
- Sector erase time: 150ms typical
- Block erase time 800ms typical
- Chip erase time: 18 Seconds typical
- Lockable 512 byte OTP security sector
- Minimum 100K endurance cycle
- Package Options
- 8 pins SOP 200mil body width
- 8 contact VDFN
- 8 pins PDIP
- 16 pin SOP 300mil body width
- All Pb-free packages are RoHS compliant
- Industrial temperature Range
F16-100HIP pinout
| Name | Description |
|---|---|
| CLK | The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI Mode") |
| DI | The SPI Serial Data Input (DI) pin provides a means for instructions, addresses and data to be serially written to (shifted into) the device. Data is latched on the rising edge of the Serial Clock (CLK) input pin |
| DO | The SPI Serial Data Output (DO) pin provides a means for data and status to be serially read from (shifted out of) the device. Data is shifted out on the falling edge of the Serial Clock (CLK) input pin |
| CS# | The SPI Chip Select (CS#) pin enables and disables device operation. When CS# is high the device is deselected and the Serial Data Output (DO) pin is at high impedance. When deselected, the devices power consumption will be at standby levels unless an internal erase, program or status register cycle |
| WP# | The Write Protect (WP#) pin can be used to prevent the Status Register from being written. Used in conjunction with the Status Register’s Block Protect (BP0, BP1and BP2) bits and Status Register Protect (SRP) bits, a portion or the entire memory array can be hardware protected. |
| HOLD# | The HOLD pin allows the device to be paused while it is actively selected. When HOLD is brought low, while CS# is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored (don’t care). The hold function can be useful when multiple devices are sharing the same SPI |
| Vcc | --- |
| Vss | --- |
Absolute maximum ratings
| Parameter | Value | Unit |
|---|---|---|
| Storage Temperature | -65 to +125 | °C |
| Plastic Packages | -65 to +125 | °C |
| Output Short Circuit Current1 | 200 | mA |
| Input and Output Voltage (with respect to ground) 2 | -0.5 to +4.0 | V |
| Vcc | -0.5 to +4.0 | V |
F16-100HIP applications
- Hydraulic Systems
- Fluid Power Equipment
- Industrial Machinery
- Hydraulic Pumps and Motors
- Heavy-Duty Construction Equipment
Comments 0
Leave a comment