XBee ZigBee S2C RF Communication Module
XBee ZigBee S2C overview
XBee ZigBee S2C RF Wireless Communication Module works with the ZigBee mesh communication protocols coordinated by the IEEE 802.15.4 PHY protocol. The module provides wireless connectivity to end-point devices in any ZigBee mesh network including devices from other vendors.
XBee ZigBee S2C RF Wireless Communication Module modules seamlessly interface with compatible gateways, device adapters, and range extenders, providing developers with true beyond-the-horizon connectivity.
Key specifications
Transmission Frequency
2.4GHz to 2.5GHz
Number of Channels
16 Direct Sequence Channels
Indoor/Urban Range
200ft
Outdoor RF line-of-sight Range
up to 4000ft
Transmit Power Output
6.3mW (8dBm) in Boost mode,2mW (3dBm) in Normal mode
RF Data Rate
250,000 bps
Receiver Sensitivity
-102dBm in Boost mode, -100dBm in Normal mode
Supply Voltage Range
+2.1V to +3.6V
Datasheet
xbee-s2c-module-datasheet.pdf
XBee ZigBee S2C features
- Serial data interface: UART, SPI
- Configuration method: API or at commands, local or over-the-air (OTA)
- Frequency band: ISM 2.4 GHz
- Form factor: through-hole, surface mount
- Hardware: S2C
- ADC inputs: (4) 10-Bit ADC inputs
- Digital I/O: 15
- Antenna options through-hole: PCB antenna, U.FL connector, RP-SMA connector, or integrated wire
- SMT: rf pad, PCB antenna, or U.FL connector
- Operating temperature: -40º C to +85º C
XBee ZigBee S2C pinout
| Pin | Name | Description |
|---|---|---|
| 1 | VCC | Chip Supply Voltage |
| 2 | DOUT | UART Data out |
| 3 | DIN/CONFIG | UART Data in |
| 4 | DO8 | Digital Output 8 |
| 5 | RESET | Module Reset (reset pulse >=200nS) |
| 6 | PWM0/RSSI | PWM Output 0/ Received Signal Strength Indicator |
| 7 | PWM1 | PWM Output 1 |
| 8 | Reserved | Do not connect |
| 9 | DTR/SLEEP_RQ/DI8 | Sleep Control or Digital Input 8 |
| 10 | GND | Ground |
| 11 | AD4/DIO4 | Analog Input 4/ Digital I/O 4 |
| 12 | CTS/DIO7 | Clear-To-Send Flow Control or Digital I/O 7 |
| 13 | ON/SLEEP | Module Status Indicator,High = ON, Low = SLEEP |
| 14 | VREF | Reference Voltage for ADC |
| 15 | ASSOCIATE/AD5/DIO5 | Associated Indicator, Analog Input 5 or Digital I/O 5 |
| 16 | RTS/AD6/DIO6 | Request-To-Send Flow Control, Analog Input 6 or Digital I/O 6 |
| 17 | AD3/DIO3 | Analog Input 3 or Digital I/O 3 |
| 18 | AD2/DIO2 | Analog Input 2 or Digital I/O 2 |
| 19 | AD1/DIO1 | Analog Input 1 or Digital I/O 1 |
| 20 | AD0/DIO0 | Analog Input 0 or Digital I/O 0 |
XBee ZigBee S2C specifications
| Transmission Frequency | 2.4GHz to 2.5GHz |
|---|---|
| Number of Channels | 16 Direct Sequence Channels |
| Indoor/Urban Range | 200ft |
| Outdoor RF line-of-sight Range | up to 4000ft |
| Transmit Power Output | 6.3mW (8dBm) in Boost mode,2mW (3dBm) in Normal mode |
| RF Data Rate | 250,000 bps |
| Receiver Sensitivity | -102dBm in Boost mode, -100dBm in Normal mode |
| Supply Voltage Range | +2.1V to +3.6V |
| Operating Current | 33mA (at3.3V, for Normal mode) , 45mA (at 3.3V,for Boost mode) |
| Idle Current | 9mA |
| Maximum output current on all pins together | 40mA |
| Power-down Current | <1uA @25C |
| ESD protection | 3000V |
XBee ZigBee S2C applications
- Industrial application control
- Smart energy
- Medium range wireless communication
More about XBee ZigBee S2C
XBee/ZigBee S2C RF Module Specifications
- Featured with UART (250 Kb/s maximum) and SPI (5 Mb/s maximum) interface
- Featured with software adjustable transmitting power
Datasheet
See Also: CD4059 Program Divide-by-N Counter | CD4048 CMOS Multifunction Expandable 8-Input Gate | 74LS122 Retriggerable Monostable Multivibrator
Comments 0
Leave a comment